- 產品描述
流感B病毒抗原快速檢測試劑盒(膠體金法)
廣州健侖生物科技有限公司
廣州健侖長期供應各種流感檢測試劑,包括進口和國產的品牌,主要包括日本富士瑞必歐、日本生研、美國BD、美國NovaBios、美國binaxNOW、凱必利、廣州創侖等主流品牌。
流感B病毒抗原快速檢測試劑盒(膠體金法)
我司還提供其它進口或國產試劑盒:登革熱、瘧疾、流感、A鏈球菌、合胞病毒、腮病毒、乙腦、寨卡、黃熱病、基孔肯雅熱、克錐蟲病、違禁品濫用、肺炎球菌、軍團菌、化妝品檢測、食品安全檢測等試劑盒以及日本生研細菌分型診斷血清、德國SiFin診斷血清、丹麥SSI診斷血清等產品。
歡迎咨詢
歡迎咨詢2042552662
想了解更多的產品及服務請掃描下方二維碼:
【公司名稱】 廣州健侖生物科技有限公司
【市場部】 楊永漢
【】
【騰訊 】 2042552662
【公司地址】 廣州清華科技園創新基地番禺石樓鎮創啟路63號二期2幢101-103室
(四)透明
透明的目的是將脫水劑從材料中除去,使材料透明,增記折光系數;同時便于下步的浸蠟和包埋等程序(因為究竟不能溶解石蠟)。透明劑是一種既能與脫水劑混合,又能與包埋劑混合的藥劑。常用的透明劑為二甲苯和綠方,適用原則也是逐級進行,可減少材料收縮。一般步驟是:2/3純酒精+1/3二甲苯→1/2純酒精+1/2二甲苯→1/3純酒精+2/3二甲苯→二甲苯(兩次),每級停留時間0.5~2小時或更長些。二甲苯穿透能力強,但又宜使材料收縮變脆,使用時不能在其中停留時間過長。若材料放入二甲苯中時有白色混濁現象發生,說明材料脫水不*,應把材料退回至純酒精中再行脫水。
(五)浸蠟
浸蠟的目的是逐漸除去透明劑,并為包埋劑所代替。常用的包埋劑是石蠟。浸蠟過程是使石蠟慢慢溶于浸有材料的透明劑中,溶解在透明劑中的石蠟漸漸深入到材料的細胞中去,zui后使透明劑*被石蠟取代,以便切片。
一般所用的石蠟分軟蠟(熔點40℃ 以下)和硬蠟(熔點40℃以上)。浸蠟過程一般是從低溫到高溫、從低熔點到高熔點逐漸進行,這一過程不能操之過急,否則浸蠟不*影響切片。此外,軟材料可用熔點較低石蠟,較硬的材料可用熔點較高的石蠟;冬季可用熔點較低的石蠟,夏季可用熔點較高的石蠟。石蠟必須純凈,不含雜質。整個浸蠟過程需在恒溫箱內進行(按需要調整溫度)。材料zui后一次二甲苯透明后即可浸蠟,浸蠟過程中逐漸使二甲苯揮發,并不斷加入純石蠟,直至石蠟飽和為止。浸蠟時間大約1~2天。
(D) transparent
The purpose of transparency is to remove the dehydrating agent from the material, making the material transparent and adding a refractive index, while facilitating the next step of immersion and embedding (because of the inability to dissolve the paraffin). A clearing agent is an agent that can be mixed with a dehydrating agent and with an embedding agent. Commonly used transparent agent for the xylene and green side, the applicable principle is also step by step, can reduce material shrinkage. The general procedure is: 2/3 pure alcohol +1/3 xylene → 1/2 pure alcohol +1/2 xylene → 1/3 pure alcohol +2/3 xylene → xylene (twice), each stage of stay Time 0.5 ~ 2 hours or longer. Xylene penetration ability, but should make the material shrinkage brittle, when used can not stay in it for too long. If the material into the xylene when white turbidity occurs, indicating that the material is not compley dehydrated, the material should be returned to pure alcohol dehydration again.
(E) Baptist wax
The purpose of the dip wax is to gradually remove the clarifier and replace it with the embedding agent. Common embedding agent is paraffin. Baptist waxing process is slowly dissolve the paraffin in the transparent material soaked in the paraffin dissolved in the transparent agent gradually into the material cells, and finally to make the transparent agent compley replaced by paraffin, in order to slice.
Paraffin wax generally used points (soft point below 40 ℃) and hard wax (melting point of 40 ℃ or more). Baptist waxing process is generally from low temperature to high temperature, from low melting point to high melting point gradually, this process can not be hasty, or not compley affect the slicing dip wax. In addition, the lower melting point of soft materials available paraffin, harder materials available higher melting paraffin; available winter melting lower paraffin, paraffin melting point in summer available higher. Paraffin wax must be pure, free of impurities. The whole process of waxing needs to be carried out in the incubator (adjust the temperature as needed). After the last time the material is transparent, xylene can be dipped in wax, the xylene is gradually volatilized during the dipped wax, and pure paraffin is continuously added until the wax is saturated. Baptist wax time of about 1 to 2 days.